debian-mirror-gitlab/doc/administration/geo/disaster_recovery/bring_primary_back.md

64 lines
3.1 KiB
Markdown
Raw Normal View History

2020-06-23 00:09:42 +05:30
---
stage: Enablement
group: Geo
info: To determine the technical writer assigned to the Stage/Group associated with this page, see https://about.gitlab.com/handbook/engineering/ux/technical-writing/#designated-technical-writers
type: howto
---
2019-09-30 21:07:59 +05:30
# Bring a demoted primary node back online **(PREMIUM ONLY)**
2019-07-31 22:56:46 +05:30
After a failover, it is possible to fail back to the demoted **primary** node to
restore your original configuration. This process consists of two steps:
1. Making the old **primary** node a **secondary** node.
1. Promoting a **secondary** node to a **primary** node.
CAUTION: **Caution:**
If you have any doubts about the consistency of the data on this node, we recommend setting it up from scratch.
## Configure the former **primary** node to be a **secondary** node
Since the former **primary** node will be out of sync with the current **primary** node, the first step is to bring the former **primary** node up to date. Note, deletion of data stored on disk like
repositories and uploads will not be replayed when bringing the former **primary** node back
into sync, which may result in increased disk usage.
2020-04-22 19:07:51 +05:30
Alternatively, you can [set up a new **secondary** GitLab instance](../replication/index.md#setup-instructions) to avoid this.
2019-07-31 22:56:46 +05:30
To bring the former **primary** node up to date:
1. SSH into the former **primary** node that has fallen behind.
1. Make sure all the services are up:
2020-03-13 15:44:24 +05:30
```shell
2019-09-30 21:07:59 +05:30
sudo gitlab-ctl start
```
2020-04-22 19:07:51 +05:30
NOTE: **Note:** If you [disabled the **primary** node permanently](index.md#step-2-permanently-disable-the-primary-node),
2019-09-30 21:07:59 +05:30
you need to undo those steps now. For Debian/Ubuntu you just need to run
`sudo systemctl enable gitlab-runsvdir`. For CentOS 6, you need to install
the GitLab instance from scratch and set it up as a **secondary** node by
2020-04-22 19:07:51 +05:30
following [Setup instructions](../replication/index.md#setup-instructions). In this case, you don't need to follow the next step.
2019-09-30 21:07:59 +05:30
NOTE: **Note:** If you [changed the DNS records](index.md#step-4-optional-updating-the-primary-domain-dns-record)
for this node during disaster recovery procedure you may need to [block
all the writes to this node](planned_failover.md#prevent-updates-to-the-primary-node)
during this procedure.
2019-07-31 22:56:46 +05:30
2020-04-22 19:07:51 +05:30
1. [Setup database replication](../replication/database.md). Note that in this
2019-07-31 22:56:46 +05:30
case, **primary** node refers to the current **primary** node, and **secondary** node refers to the
former **primary** node.
If you have lost your original **primary** node, follow the
2020-04-22 19:07:51 +05:30
[setup instructions](../replication/index.md#setup-instructions) to set up a new **secondary** node.
2019-07-31 22:56:46 +05:30
## Promote the **secondary** node to **primary** node
When the initial replication is complete and the **primary** node and **secondary** node are
2020-04-22 19:07:51 +05:30
closely in sync, you can do a [planned failover](planned_failover.md).
2019-07-31 22:56:46 +05:30
## Restore the **secondary** node
If your objective is to have two nodes again, you need to bring your **secondary**
node back online as well by repeating the first step
([configure the former **primary** node to be a **secondary** node](#configure-the-former-primary-node-to-be-a-secondary-node))
for the **secondary** node.