debian-mirror-gitlab/doc/administration/operations/moving_repositories.md

---
stage: none
group: unassigned
info: To determine the technical writer assigned to the Stage/Group associated with this page, see https://about.gitlab.com/handbook/engineering/ux/technical-writing/#designated-technical-writers
---

# Moving repositories managed by GitLab

Sometimes you need to move all repositories managed by GitLab to
another filesystem or another server. In this document we will look
at some of the ways you can copy all your repositories from
`/var/opt/gitlab/git-data/repositories` to `/mnt/gitlab/repositories`.

We will look at three scenarios: the target directory is empty, the
target directory contains an outdated copy of the repositories, and
how to deal with thousands of repositories.

DANGER: **Danger:**
Each of the approaches we list can/will overwrite data in the
target directory `/mnt/gitlab/repositories`. Do not mix up the
source and the target.

## Target directory is empty: use a `tar` pipe

If the target directory `/mnt/gitlab/repositories` is empty the
simplest thing to do is to use a `tar` pipe. This method has low
overhead and `tar` is almost always already installed on your system.
However, it is not possible to resume an interrupted `tar` pipe: if
that happens then all data must be copied again.

```shell
sudo -u git sh -c 'tar -C /var/opt/gitlab/git-data/repositories -cf - -- . |\
  tar -C /mnt/gitlab/repositories -xf -'
```

If you want to see progress, replace `-xf` with `-xvf`.

### `tar` pipe to another server

You can also use a `tar` pipe to copy data to another server. If your
`git` user has SSH access to the new server as `git@newserver`, you
can pipe the data through SSH.

```shell
sudo -u git sh -c 'tar -C /var/opt/gitlab/git-data/repositories -cf - -- . |\
  ssh git@newserver tar -C /mnt/gitlab/repositories -xf -'
```

If you want to compress the data before it goes over the network
(which will cost you CPU cycles) you can replace `ssh` with `ssh -C`.

## The target directory contains an outdated copy of the repositories: use `rsync`

If the target directory already contains a partial / outdated copy
of the repositories it may be wasteful to copy all the data again
with `tar`. In this scenario it is better to use `rsync`. This utility
is either already installed on your system or easily installable
via `apt`, `yum`, etc.

```shell
sudo -u git  sh -c 'rsync -a --delete /var/opt/gitlab/git-data/repositories/. \
  /mnt/gitlab/repositories'
```

The `/.` in the command above is very important, without it you can
easily get the wrong directory structure in the target directory.
If you want to see progress, replace `-a` with `-av`.

### Single `rsync` to another server

If the `git` user on your source system has SSH access to the target
server you can send the repositories over the network with `rsync`.

```shell
sudo -u git sh -c 'rsync -a --delete /var/opt/gitlab/git-data/repositories/. \
  git@newserver:/mnt/gitlab/repositories'
```

## Thousands of Git repositories: use one `rsync` per repository

Every time you start an `rsync` job it has to inspect all files in
the source directory, all files in the target directory, and then
decide what files to copy or not. If the source or target directory
has many contents this startup phase of `rsync` can become a burden
for your GitLab server. In cases like this you can make `rsync`'s
life easier by dividing its work in smaller pieces, and sync one
repository at a time.

In addition to `rsync` we will use [GNU
Parallel](http://www.gnu.org/software/parallel/). This utility is
not included in GitLab so you need to install it yourself with `apt`
or `yum`. Also note that the GitLab scripts we used below were added
in GitLab 8.1.

**This process does not clean up repositories at the target location that no
longer exist at the source.** If you start using your GitLab instance with
`/mnt/gitlab/repositories`, you need to run `gitlab-rake gitlab:cleanup:repos`
after switching to the new repository storage directory.

### Parallel `rsync` for all repositories known to GitLab

This will sync repositories with 10 `rsync` processes at a time. We keep
track of progress so that the transfer can be restarted if necessary.

First we create a new directory, owned by `git`, to hold transfer
logs. We assume the directory is empty before we start the transfer
procedure, and that we are the only ones writing files in it.

```shell
# Omnibus
sudo mkdir /var/opt/gitlab/transfer-logs
sudo chown git:git /var/opt/gitlab/transfer-logs

# Source
sudo -u git -H mkdir /home/git/transfer-logs
```

We seed the process with a list of the directories we want to copy.

```shell
# Omnibus
sudo -u git sh -c 'gitlab-rake gitlab:list_repos > /var/opt/gitlab/transfer-logs/all-repos-$(date +%s).txt'

# Source
cd /home/git/gitlab
sudo -u git -H sh -c 'bundle exec rake gitlab:list_repos > /home/git/transfer-logs/all-repos-$(date +%s).txt'
```

Now we can start the transfer. The command below is idempotent, and
the number of jobs done by GNU Parallel should converge to zero. If it
does not, some repositories listed in `all-repos-1234.txt` may have been
deleted/renamed before they could be copied.

```shell
# Omnibus
sudo -u git sh -c '
cat /var/opt/gitlab/transfer-logs/* | sort | uniq -u |\
  /usr/bin/env JOBS=10 \
  /opt/gitlab/embedded/service/gitlab-rails/bin/parallel-rsync-repos \
    /var/opt/gitlab/transfer-logs/success-$(date +%s).log \
    /var/opt/gitlab/git-data/repositories \
    /mnt/gitlab/repositories
'

# Source
cd /home/git/gitlab
sudo -u git -H sh -c '
cat /home/git/transfer-logs/* | sort | uniq -u |\
  /usr/bin/env JOBS=10 \
  bin/parallel-rsync-repos \
    /home/git/transfer-logs/success-$(date +%s).log \
    /home/git/repositories \
    /mnt/gitlab/repositories
`
```

### Parallel `rsync` only for repositories with recent activity

Suppose you have already done one sync that started after 2015-10-1 12:00 UTC.
Then you might only want to sync repositories that were changed via GitLab
_after_ that time. You can use the `SINCE` variable to tell `rake
gitlab:list_repos` to only print repositories with recent activity.

```shell
# Omnibus
sudo gitlab-rake gitlab:list_repos SINCE='2015-10-1 12:00 UTC' |\
  sudo -u git \
  /usr/bin/env JOBS=10 \
  /opt/gitlab/embedded/service/gitlab-rails/bin/parallel-rsync-repos \
    success-$(date +%s).log \
    /var/opt/gitlab/git-data/repositories \
    /mnt/gitlab/repositories

# Source
cd /home/git/gitlab
sudo -u git -H bundle exec rake gitlab:list_repos SINCE='2015-10-1 12:00 UTC' |\
  sudo -u git -H \
  /usr/bin/env JOBS=10 \
  bin/parallel-rsync-repos \
    success-$(date +%s).log \
    /home/git/repositories \
    /mnt/gitlab/repositories
```